Remington 104316-04, 104316-05, 106890-01, 106890-02, 108526-01, 104317, 106821, 106821A Owner's Manual download pdf (Page 17)

108539

www.desatech.com

2. Turn adjusting screw clockwise until all slack is

out of chain (see Figure 5).

Note: There should

be no gap between side links of chain and bottom

of guide bar (see Figure 6).

3. Wearing protective gloves, move chain around

guide bar. Chain should move freely. If chain

does not move freely, loosen chain by turning

adjusting screw counterclockwise.

4. After chain tension is correct, tighten guide

bar nuts ﬁrmly. If not, guide bar will move and

loosen chain tension. This will increase the risk

of kickback. This can also damage saw.

Note:

A new chain will stretch. Check new chain after

ﬁrst few minutes of operation. Allow chain to

cool down. Readjust chain tension.

SAW CHAIN TENSION

ADJUSTMENT

Continued

FILLING OIL TANK

1. Remove oil cap.

2. Fill oil tank with SAE #30 motor oil.

Note: For

temperatures below 30°F, use SAE #10 oil. For

temperatures above 75°F, use SAE #40 oil.

3. Replace oil cap at once. Tighten oil cap ﬁrmly for

good seal. This will avoid oil seepage from tank.

4. Wipe off excess oil.

Note:

It is normal for oil to seep when saw is not in use.

Empty oil tank after each use to prevent seepage.

OPERATING CHAIN SAW

EXTENSION CORDS

Use proper extension cords with this saw. Use only

extension cords marked for outdoor use. The cord

must be marked with sufﬁx W or W-A following

the cord type designation. Example: SJTW-A or

SJTW.

Use proper sized cord with this saw. Cord must be

heavy enough to carry current needed. An undersized

cord will cause voltage drop at saw. Saw will lose

power and overheat. Follow cord size requirements

listed below.

WARNING: Read and understand this

owner’s manual before operating this saw.

Make certain you read and understand all

Important Safety Information, pages 2

through 4. Improper use of this chain saw

can cause severe injury or death from

ﬁre, electrical shock, or body contact with

moving chain, or falling wood.

Cord Length AWG Cord Size

25 feet 16 AWG

50 feet 16 AWG

100 feet 16 AWG

150 feet 14 AWG

Models Pole Saw Assy: 104317, 106821, 106821A,

and PS1510A; Pole Saw: 104316-04, 104316-05

(8˝/20.3 cm), 106890-01, 106890-02 (10˝/25.4 cm),

and 108526-01 [8˝(20.3 cm), 10˝ (25.4 cm)]

OILING CHAIN

Always check oil level before using saw. Do not attempt

to operate the oil system while saw is in operation. To oil

chain, press squeeze bulb. Oil will feed onto the guide bar

and chain. Press squeeze bulb at least once before each

cut. Check oil level often by looking at oil sight level

hole. Oil sight level hole is on left side of saw, between

front handle and front hand guard.

CUTTING WITH THE CHAIN SAW

1. Connect saw to extension cord. Connect exten-

sion cord to power supply.

2. Make sure section of log to be cut is not laying

on ground. This will keep chain from touching

ground as it cuts through log. Touching ground

with moving chain will dull chain.

3. Use both hands to grip saw. Always use left hand

to grip front handle and right hand to grip rear

handle. Use ﬁrm grip. Thumbs and ﬁngers must

wrap around saw handles (see Figure 9).

4. Make sure your footing is ﬁrm. Keep feet apart.

Divide your weight evenly on both feet.

5. When ready to make a cut, press in switch lockout

with right thumb and squeeze trigger (see Figure

9). This will turn saw on. Releasing trigger will

turn saw off. Make sure saw is running at full speed

before starting a cut.

Continued

Keep cord away from cutting area. Make sure cord

does not catch on branches or logs during cutting.

Inspect cords often. Replace damaged cords.

The extension cord may come undone from the power

cord during use. To avoid this, make a knot with the

two cords as shown in Figure 7.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 50 51

Comments to this Manuals

No comments

Remington 104316-04, 104316-05, 106890-01, 106890-02, 108526-01, 104317, 106821, 106821A Owner's Manual Page 17

Comments to this Manuals

Related products and manuals for Power chainsaws Remington 104316-04, 104316-05, 106890-01, 106890-02, 108526-01, 104317, 106821, 106821A