Remington R-1000 Owner's Manual download pdf (Page 11)

To Assemble (

Model 11-87™)

WARNING:

MODEL 11-87™ BARRELS CAN NOT BE USED AS REPLACEMENT BARRELS ON MODEL 1100 FIREARMS.

MODEL 1100 BARRELS CAN NOT BE USED AS REPLACEMENT BARRELS ON MODEL 11-87 FIREARMS.

MODEL 11-87 SUPER MAGNUM™ BARREL REPLACEMENT:

ONLY MODEL 11-87 12-GAUGE BARRELS HAVING 3

⁄2" CHAMBERS CAN BE USED ON MODEL 11-87 SUPER

MAGNUM RECEIVERS.

NEVER ATTEMPT TO ASSEMBLE ANY MODEL 11-87 12-GAUGE BARREL WITH A CHAMBER LENGTH SHORTER

THAN 3

⁄2" TO A RECEIVER MARKED MODEL 11-87 SUPER MAGNUM.

NOTE:

The barrel and chamber should be cleaned before assembling the firearm. Clean the barrel following

the instructions on page 16.

1. Point the firearm in a safe direction.

2. Engage the safety mechanism.

RED BAND WILL NOT SHOW.

3. Pull the operating handle fully rearward to open the action.

4. Unscrew and remove the magazine cap.

5. Slide the fore-end forward and remove it from the magazine tube.

6. Remove the cardboard packing ring from the magazine tube.

7. Remove the wire tie from the gas cylinder and gas cylinder collar. See Picture 9 on page 10.

8. Hold the barrel in front of the gas cylinder with gas cylinder collar attached. See Picture 12.

NOTE:

A gas cylinder collar is not used on the 20-ga. models or the

11-87 12-ga. Super Magnum models.

9. Place the gas cylinder over the end of the magazine tube.

10. Align the long slot on the rear of the barrel with the stud projecting

from the inside of the receiver. See Picture 11 on page 10.

11. Seat the barrel firmly into the receiver.

12. Slide the fore-end over the magazine tube.

13. Replace and tighten the magazine cap.

FOR MODEL 11-87 SPORTING CLAYS GRADE SEE NOTE BELOW.

NOTE:

The Model 11-87 Sporting Clays grade uses a rubber grommet in the fore-end. Assemble fore-end

using the following instructions.

1. Check the position of the rubber grommet in the fore-end. Raised lump MUST be in the recess of fore-end.

See Picture 13.

2. Place assembled gun upright on butt and tilt slightly toward the heel allowing the gas cylinder collar to

rest in its proper position against the gas cylinder.

3. Slide the fore-end over the magazine tube while holding the fore-end as

straight to the magazine tube as possible. Push down until at least two

(2) threads on the magazine tube are showing in front of the fore-end.

4. Replace and tighten the magazine cap.

To Load and Unload

MODEL 11-87 SUPER MAGNUM OWNERS PLEASE NOTE:

A BARREL SEAL ACTIVATOR IS USED ON THE MODEL 11-87 SUPER MAGNUM FOR 2

⁄4" LOADS. MAKE SURE THE

BARREL SEAL ACTIVATOR IS IN THE CORRECT POSITION (SEE PICTURE 31, PAGE 17) FOR USE WITH 2

⁄4" LOADS.

REMOVAL OF THE BARREL SEAL ACTIVATOR IS RECOMMENDED WHEN USING 3" OR 3

⁄2" LOADS.

NOTE:

The 11-87 Super Magnum is designed to function optimally with ammunition ranging from 2

⁄4" 3 dram

⁄8 oz. loads, up to 3

⁄2" Magnum loads. Loads lighter than 2

⁄4" 3 dram 1

⁄8 oz. loads may not create enough

energy to fully cycle the bolt of the firearm.

WARNING:

Always check the shell for the correct gauge and length before loading the firearm.

PICTURE 12

PICTURE 13

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 25 26

Comments to this Manuals

No comments

Remington R-1000 Owner's Manual Page 11

Comments to this Manuals

Related products and manuals for Men's shavers Remington R-1000