Remington 104317 Owner's Manual download pdf (Page 6)

6

107996

8' ELECTRIC TELESCOPING POLE SAW

®

For more information, visit www.desatech.com

OPERATING POLE

SAW

WARNING: Read and under-

stand this owner’s manual be-

fore operating this Pole Saw.

Make certain you read and un-

derstand all Safety Warnings.

Improper use of this Pole Saw

can cause severe injury or death

from fire, electrical shock, or body

contact with moving chain, or

falling wood.

EXTENSION CORDS

Use proper extension cords with this Pole

Saw. Use only extension cords marked for

outdoor use. The cord must be marked with

suffix W or W-A following the cord type

designation.

Example:

SJTW-A or SJTW.

Use proper size cord with this saw. Cord

must be heavy enough to carry current

needed. An undersized cord will cause volt-

age drop at saw. Saw will lose power and

overheat. Follow cord size requirements

listed below.

Cord Length AWG cord size

25 feet 16

50 feet 16

100 feet 16

150 feet 14

Keep cord away from cutting area. Make

sure cord does not catch on branches or logs

during cutting. Inspect cords often. Replace

damaged cords. The extension cord may

come undone from the power cord during

use. To avoid this, make a knot with the two

cords as shown in Figure 7.

UNLOCK

LOCK

Figure 8 - Extending Telescopic Pole

ADJUSTING POLE LENGTH

The Remington Pole Saw has a telescoping

pole assembly that will extend from 57

inches (fully retracted) to 96 inches (fully

extended). A threaded compression cou-

pling is used to hold the pole in position at

any extended length.

1. To extend the pole, loosen coupling by

turning coupling nut counterclockwise

as shown in Figure 8.

2. Pull inner pole section out to desired

length of extension.

Note:

Only extend

pole to minimum length required to

reach limb that is being cut.

3. To lock pole in position, tighten cou-

pling by turning coupling nut clockwise

(see Figure 8) until firmly hand tight.

Make sure saw handle is aligned with

pole handle before tightening coupling

nut.

IMPORTANT:

Do not use wrench

or pliers to overtighten coupling. Dam-

age to coupling or pole may result.

Extension

Cord

Chain Saw

Power Cord

Figure 7 - Tying Extension Cord and Power

Cord in Knot

OILING CHAIN

To oil chain, press squeeze bulb on oil cap.

Oil will feed onto guide bar and chain. Press

squeeze bulb on oil cap at least once before

each cut. Always check oil level before

using Pole Saw. Check oil level often by

looking at oil sight level hole. Oil sight level

hole is on left side of saw, between front

handle and front hand guard. Do not attempt

to operate the oiler while cutting with the

Pole Saw.

Figure 5 - Bracket with Trigger Support

Trigger

Support

Bracket

Figure 6 - Assembly of Pole Saw Brackets

ASSEMBLY OF POLE SAW

1. Slip handle bracket over chain saw

handle from the right side (see Figure 5).

Note:

The trigger must be depressed

before the bracket will go onto the

handle.

Push the lockout button and depress the

trigger. While holding the trigger in,

place the trigger support portion of the

bracket under the trigger and slide the

bracket onto the chain saw handle. The

bracket will keep the trigger in the “on”

position.

2. Align holes in pole bracket with holes

in handle bracket. Install Phillips head

screws with lockwashers through pole

bracket from left side and thread into

the weld nuts on the handle bracket.

Tighten screws securely by hand.

3. Plug the saw power cord into receptacle

cord at end of inner pole.

ASSEMBLY

Continued

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments