Remington MB-100 Owner's Manual download pdf (Page 15)

3. Place a drop of Rem™ Oil in each of the four points in the trigger assembly specified in Picture 17.

14. Place the safety in the fire “F” position. Pull the trigger rearward and release multiple times. Ensure the trig-

ger returns completely to the forward position each time.

If the trigger does not completely return,

reassemble the rifle and return it to a Remington

Authorized Service Center.

WARNING! If the trigger does not fully return to the forward position each time it is released, then your rifle is NOT in a

safe operating condition and it must NOT be used until you have had it inspected by a Remington Authorized Service Center.

Use of a firearm in an unsafe operating condition may result in injury or death to you or a bystander and severe

damage to the firearm.

15. If the trigger completely returns as specified in operation 14, pull and hold the trigger rearward and using

a small punch or screwdriver depress the sear and release multiple times. The sear must return to the full

upward position without hesitation.

If the sear does not freely return, reassemble the rifle and

return it to a Remington Authorized Service Center.

WARNING! If the sear does not return to the full upward position without hesitation, then your rifle is NOT in a safe

operating condition and it must NOT be used until you have had it inspected by a Remington Authorized Service Center.

Use of a firearm in an unsafe operating condition may result in injury or death to you or a bystander and severe

damage to the firearm.

16. If the sear freely returns to the full upward position as specified in operation 15, release the trigger and

operate the safety from the fire “F” to the safe “S” position multiple times. The safety must operate freely.

The safety detent spring must position the safety in the full safe “S” or fire “F” position. The safety should

not remain in a position anywhere between the full safe “S” or fire “F” position. If the safety does not freely

return to the full safe “S” or fire “F” position, repeat operations 8 thru 16.

If the safety does not freely

return to the safe “S” or fire “F” position after repeating operations 8 thru 16, return the firearm

to a Remington Authorized Service Center for an inspection of the safety and trigger assembly.

17. Place the safety in the safe “S” position and lightly spray Rem™ Oil on all the external surfaces of the

trigger assembly and receiver. Wipe off excess oil.

TO ASSEMBLE MODELS WITHOUT A FLOOR PLATE:

1. Always point the firearm in a safe direction.

2. Put the magazine follower and the spring into the magazine.

3. Put the stock over the receiver and trigger assembly.

4. Replace and tighten the trigger guard (stock) screws.

WARNING! Before you replace the bolt assembly, make sure the barrel is free from obstructions.

5. Replace the bolt assembly. See instructions on page 9.

TO ASSEMBLE MODELS WITH A FLOOR PLATE ONLY:

Put the magazine all the way into the bottom of the receiver.

MODELS WITH FLOOR PLATE OR DETACHABLE MAGAZINE:

1. Always point the firearm in a safe direction.

2. Assemble the trigger guard assembly on the stock.

3. Put the stock over the receiver and trigger assembly.

4. Replace and tighten the trigger guard (stock) screws.

5. Close the floor plate or replace detachable magazine.

WARNING! Before you replace the bolt assembly, make sure the barrel is free of obstructions.

6. Replace the bolt assembly. See Instructions on page 9.

WARNING! After cleaning the trigger assembly, check the chamber and magazine to make sure there are no

cartridges in the firearm. Put the safety mechanism in the ‘F’ position. Close the bolt smartly. The firing pin must

remain cocked. To check, pull the trigger. The firing pin must fall. Repeat the test at least ten times. If the firing

pin will not remain cocked when the bolt is closed smartly, return the firearm to the factory or a

REMINGTON

AUTHORIZED SERVICE CENTER

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Comments to this Manuals

No comments

Remington MB-100 Owner's Manual Page 15

Comments to this Manuals

Related products and manuals for Grass trimmers Remington MB-100