Remington LNT-2 User Manual download pdf (Page 21)

108539 www.desatech.com

4. Hold ﬁle guide level. Make sure 30° mark on

ﬁle guide is parallel to center of guide bar (see

Figure 19). This will insure that you ﬁle cutters

at 30° angle.

5. File from inside towards outside of cutter until

sharp. Only ﬁle in this one direction (see Figure

19).

Note:

Two or three strokes with ﬁle should

sharpen cutter.

6. After each cutter is sharpened, move chain for-

ward to sharpen next cutter. File all cutters on

one side of chain.

7. Move to other side of chain and repeat process.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cut-

ters are sharpened. After every second or third sharp-

ening, reset cutter depth gauges.

1. Place depth gauge tool (.025") ﬁrmly across top

of two cutters. Make sure depth gauge enters slot

in depth gauge tool (see Figure 21).

2. Use medium ﬂat ﬁle. File depth gauge level with

depth gauge tool.

3. Remove depth gauge tool. With ﬂat ﬁle, round

off front corner of cutter depth gauge (see Fig-

ure 22).

After several hand ﬁlings, have authorized service

center or sharpening service machine sharpen chain.

This will insure even ﬁling.

REPLACING SAW CHAIN

Replace chain when cutters are too worn to sharpen or

when chain breaks. Only use replacement chain noted

in this manual. Always include new drive sprocket when

replacing chain. This will maintain proper driving of

chain.

Note:

For proper chain and drive sprocket, see

Replacement Parts and Accessories.

CLEANING AND

MAINTENANCE

Continued

TECHNICAL SERVICE

You may have further questions about assembling,

operating, or maintaining this saw. If so, contact

DESA International’s Technical Service Department

at 1-800-858-8501.

You can also visit DESA International’s technical

service web site at www.desatech.com.

SERVICE PUBLICATIONS

You can receive an illustrated parts list free of charge.

Send a self-addressed stamped envelope to address

on back page of this manual.

When writing, include model number and serial num-

ber of saw. You will ﬁnd these numbers on saw mo-

tor housing decal.

REPLACEMENT PARTS

AND ACCESSORIES

WARNING: Use only replacement

parts and accessories described in this

manual. Use of other parts or accessories

could damage saw or injure operator.

For a list of Authorized Service Centers or Parts Dis-

tributors near you, call 1-800-858-8501 or visit our

website at www.desatech.com.

You may purchase the following service or replace-

ment parts:

LNT-2

Part Number Description

104302-01S

Guide bar, 8" (20.3 cm)

104301S

Chain, 8" (20.3 cm)

097567-01S Guide bar, 10" (25.4 cm)

091371S Chain, 10" (25.4 cm)

097568-02S Guide bar, 12" (30.5 cm)

091373-02S Chain, 12" (30.5 cm)

075752 Drive Sprocket

099178H, 100089-06, 100089-07 & EL-1

Part Number Description

097570-01S Guide bar, 14" (35.5 cm)

091374-02S Chain, 14" (35.5 cm)

075752 Drive Sprocket

DESA International

P.O. Box 90004

Bowling Green, KY 42102-9004

1-800-858-8501

Parts Department

STORAGE

If storing saw for more than 30 days, follow steps below.

1. Drain oil tank.

2. Remove and clean guide bar and chain. Clean

guide bar and chain by soaking in petroleum

based solvent or mild soap and water mixture.

3. Dry guide bar and chain.

4. Place chain in container ﬁlled with oil. This will

prevent rust.

5. Wipe a thin coating of oil over surface of guide bar.

6. Wipe off outside of saw body. Do this with soft cloth

dampened with a mild soap and water mixture.

7. Store chain saw

• in a high or locked place, out of children’s reach

• in a dry place

• in a carrying case or with scabbard over guide bar

Continued

Must order both pieces

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 51 52

Comments to this Manuals

No comments

Remington LNT-2 User Manual Page 21

Comments to this Manuals

Related products and manuals for Petrol tool Remington LNT-2