Remington LNT-2 User Manual download pdf (Page 16)

108539www.desatech.com

Replacement Chain Chain that complies with ANSI

B175.1 when used with a speciﬁc saw. It may not

meet ANSI requirements when used with other saws.

Saw Chain (Chain) Loop of chain having cutting

teeth for cutting wood. The motor drives chain. The

guide bar supports chain.

Spiked Bumper (Spike) Pointed teeth at front of

saw body beside guide bar. Keep spiked bumper in

contact with wood when felling or bucking. It helps

maintain position of saw while cutting.

Sprocket Toothed wheel that drives chain.

Switch Device that completes or interrupts electri-

cal circuit to motor of saw.

Switch Linkage This device connects switch to trig-

ger. It moves switch when you squeeze trigger.

Switch Lockout Device that reduces accidental start-

ing of saw.

Trigger Device that turns saw on and off. Squeezing

trigger turns saw on. Releasing trigger turns saw off.

Trimming (Pruning) Process of cutting limb(s) from

a living tree.

Undercut An upward cut from underside of log or

limb. This is done while in normal cutting position

and cutting with top of guide bar.

ASSEMBLY

Note:

Some models are pre-assembled. Assembly

is not needed on these models.

See Saw Chain Tension Adjustment, pages 16 and 17.

The plastic hardware bag should include:

•two guide bar bolts

•two guide bar nuts

• one Phillips-head tapping screw

• automatic chain sharpener (Fast Sharp models only)

1. Lay chain out ﬂat.

2. Install front hand guard onto saw body. Do this by

pressing two mounting stand-outs on hand guard

into hex-shaped holes in saw body (see Figure 3).

3 Insert tapping screw through hand guard and into

saw handle. Tighten screw ﬁrmly.

4. Turn adjusting screw counterclockwise (see Fig-

ure 4). Continue to turn adjusting screw until

adjusting block is to rear of adjusting plate.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

IMPORTANT: Do not clamp chain saw in

vise during assembly.

CAUTION: Do not place chain on

saw backwards. If chain is backwards,

saw will vibrate badly and will not cut.

CHAIN SAW NAMES AND

TERMS

Continued

5. Install guide bar onto saw body. Place rear of

guide bar between adjusting plate and sprocket

support.

IMPORTANT:

Make sure to insert adjusting

block into oval adjusting hole on guide bar.

6. Line up holes on sprocket support with center

slot on guide bar and holes in saw body.

7. Insert guide bar bolts through front hand guard,

saw body, center slot of guide bar, and sprocket

support. Attach guide bar nuts to guide bar bolts.

IMPORTANT:

Tighten guide bar nuts ﬁnger

tight only. Make sure adjusting block is in oval

adjusting hole on guide bar.

8. Place chain around drive sprocket, then along top

groove of guide bar and around guide bar nose.

Note:

Make sure cutting edges of chain are fac-

ing the right direction. Position chain so cutting

edges on top of guide bar face guide bar nose

(see Figure 3).

Note:

For pre-assembled models, the saw chain ten-

sion is properly set at factory. A new chain will

stretch. Check new chain after first few minutes of

operation. Allow chain to cool down. Follow steps

below to readjust saw chain tension.

1. Before adjusting chain, make sure guide bar nuts

are only ﬁnger tight (see Figure 3). Also make

sure adjusting block is in oval adjusting hole on

guide bar (see Figures 3 and 4).

SAW CHAIN TENSION

ADJUSTMENT

WARNING: Unplug chain saw from

power source before adjusting saw chain

tension.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

WARNING: Maintain proper chain

tension always. A loose chain will in-

crease the risk of kickback. A loose

chain may jump out of guide bar groove.

This may injure operator and damage

chain. A loose chain will cause chain,

guide bar, and sprocket to wear rapidly.

9. Adjust saw chain tension. Follow steps under

Saw Chain Tension Adjustment, pages 16 and 17.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 51 52

Comments to this Manuals

No comments

Remington LNT-2 User Manual Page 16

Comments to this Manuals

Related products and manuals for Petrol tool Remington LNT-2