Remington HC5950 User Manual download pdf (Page 3)

4 5

ENGLISH

•Topreservethelifeofyourbatteries,letthemrunoutevery6monthsthenrechargefor

90 minutes.

, CHARGING VIA STANDARD ELECTRICAL SOCKET

•Ensuretheproductisswitchedo.

•Connectthechargingadaptortotheproductandthentothemains.

•Whenchargingthedigitaldisplaywillindicatetheunitischarging

•Allow90minutesforacompletecharge.

, USB

•ConnectyourUSBcabletotheUSBportonyourpowersource.

•ConnecttheUSBcabletoyourappliance.

•DonotruntheclipperwhileconnectedtoaUSBport.Itwillonlyrunoitsbatteriesin

this condition and stop charging.

, CORDED USE

•Connectthechargingadaptortotheproductthentothemains.

•Whenthecordisconnectedtothemains,adigitaldisplaywillbedisplayedonthe

appliance.

•Theunitwillonlyrunincordedmodewhenconnectedtothemainsusingthesupplie

•Remingtonpoweradaptor,otherUSBchargerswillonlychargetheunit

A CAUTION

Extendedmainsonlyusewillresultinthereductionofthebatterylife.

, WARNING

TheappliancecannotbeoperatedincordedmodewhileconnectedtoaPCviatheUSBport.

, CORDLESS USE

Whentheunitisswitchedonandfullycharged,theproductcanbeusedincordlessmodefor

up to 40 minutes.

F HOW TO USE

, USING THE TOUCH SCREEN

, ADJUSTING THE TRIM LENGTH

• Firstselectwhichhaircomb1,2or3forthelengthrangedesired.

•Comb1(1.5mm),comb2(3mmto23mm),Comb3(22mmto42mm).Usingthecomb

selectionswitchsetthesystemtomatchthecorrespondingcomb.

• IfComb1isselected,thedisplaywillalwaysshow1.5mmor#0,asthereisno

mechanical adjustment

• ForComb2and3,thetouchbuttonscanbeusedtoadjusttothedesiredcuttinglength

followingthestepsbelow

• Withcomb2and3,installedontotheproductandthecorrespondingcombswitch

selectedadjustmentcanbegin.Alsoensurethatthelockbuttonisintheunlocked

position.

Note: Ifaredwarninglightisvisiblethroughthecombwheninstalled,thisisindication

thatthecombselectionswitchisonthewrongsetting.

• Pressandholdthearrowuptoincreasethecuttinglengthanddowntodecreaseit.The

combwillmovetoreacheachsetting,thelengthswillchangeasyouholdtheup/down

arrow,andthesettingnumberwillappearonthedigitaldisplay.

• Selectthedesiredboostlevelbypressingtheboostbuttonwiththelockinthe

unlockedposition.Thedisplaywillindicatethelevel.

• Oncethedesiredlengthandboostlevelarereached,lockthesystemusingthelock

switch.Thedisplayshouldshowaclosedlock,andthecurrentlengthsettingandboost

level.Proceedtousetheclipper

 Note:Adjustmentstolengthandboostcanbedoneanytimethelockswitchissetto

unlock.Settingcanbedonewiththemainmotoro,ifthepowerbuttonispresseda

secondtime.Toturnthemainmotorbackonthepowerbuttonneedstobepressed

again.

• Pressandholdthebatteryicontodisplaytheremainingbatterytimeinminutesonthe

digitaldisplay.Thiscanbeusedwhilsttheapplianceislocked.

, SWITCHING BETWEEN UNITS OF LENGTH (mm, #)

Holdthepowerbuttonfor3seconds,thedisplaywillshowthechangebetweenmmand#,at

thistimereleasethepowerbutton.Thesettinghasbeenchanged.

Note:Iftheusercontinuestoholdthepowerbuttonfor8seconds,thesystemwillenterreset

mode

A CAUTION

Oncethedigitaldisplaychangesfrommmtogradenumber,releasethepowerbuttontoavoid

aninadvertentrestart.

NOTE:Thecombmustbeattachedtotheapplianceinordertousethehairlengthselector.To

achieve0.4mmthecombmustberemoved.

, BEFORE STARTING THE CUT

• Inspecttheclippermakingsurethatitisfreefromhairanddirt.

• Seatthepersonsothattheirheadisapproximatelyatyoureyelevel.

• Beforecutting,alwayscombthehairsoitistanglefreeanddry.

, TO ATTACH A COMB

• Holdthecombwithitsteethupward

• Guidethecombrailsintotheslotsonthesideoftheclipperhead.Thenpushthecomb

down until it seats on the adjustment arm.

, TO REMOVE THE COMB

• Holdingtheclipperwiththebladesfacingawayfromyou,rmlypushthecombupward

andawayfromtheblades.

1 2 3 4 5 6 7 8 ... 79 80

Comments to this Manuals

No comments

Remington HC5950 User Manual Page 3

Comments to this Manuals

Related products and manuals for Hair trimmers & clippers Remington HC5950