Remington R-9500 User Manual download pdf (Page 5)

How to Use

Charging

Before using your shaver for the first time, put

it on charge for 24 hours.

Preparing the System

Cleaning solution:

1. Press the latch but-

tons on the sides of

the cleaning base and

lift the upper portion

off the unit. You will

need to keep the but-

tons pressed in as you

move the upper por-

tion away from the

base. The cleaning

solution tank is in the

unit’s bottom portion.

2. Remove the filter

from the tank and set

aside.

3. Pour the bottle of

cleaning solution into

the base of the unit

through the opening

where the filter was

removed. Fill tank to

the bottom of the fill tab.

Place the filter back into its original position.

NOTE: It is important to make sure the filter

is in place. The filter collects hair clippings

and debris, and should be replaced along

with the solution. Failure to do so will per-

manently clog the system rendering it inop-

erable.

5. Replace the top portion of the cleaning

base by lining up the three tall posts with

the three holes in the tank. Push the top

portion down until the two latches click

into place.

6. You can dispose of the bottle and cap

with your normal trash, or recycle where

local ordinances apply.

Operating the

Charging/Cleaning System

Plug the power cord into the cleaning base

and then into an electrical outlet.

Place the shaver into the unit, head side

down, and slide its “tail” toward the

“neck” of the base until it clicks into place.

Charging

Your shaver automatically begins to

recharge as soon as it clicks into place in

the cleaning base. While it is charging, the

green indicator light will flash; when it is

fully charged the green light will stop blink-

ing and glow steadily.

Cleaning

To activate cleaning mode, simply press the

CLEAN button on the cleaning base. The

amber indicator light flashes through the

entire cleaning cycle, which lasts approxi-

mately 25 minutes. When the cleaning

cycle has been completed, the amber light

will stop blinking and glow steadily. The

unit then returns to charging mode.

! Wait until the cleaning cycle has finished

before removing the shaver from the base.

If the shaver is removed during the clean-

ing cycle it will be covered with cleaning

solution and be unuseable.

Solution levels

The cleaning solution will slowly evaporate

with use. When the solution levels get low,

the red replacement indicator light will

begin to flash. This means you have

enough cleaning solution left for approxi-

mately 5 more cleanings. If the red light

stops blinking and glows steadily, the unit

will not operate until the solution and filter

have been replaced.

Replacing the Filter and Solution

Only Remington’s special cleaning solution

and filter can be used with the Smart

System. The cleaning solution contains a

high percentage of alcohol and a special oil

that lubricates your shaver each time it is

cleaned. The filter is specially designed to

collect hair debris yet allow for the system

to clean your shaver.

To refill the cleaning solution and replace

the filter, follow the steps for "Preparing the

System" above. But before replacing the

upper portion of the unit, rinse out the tank

with fresh water and allow it to air dry to

remove any sediment.

Wipe off the unit periodically with a damp

cloth and remove any hair debris that has

collected where the shaver sits.

! To avoid damage to the cleaning system,

use only Remington special cleaning

solution.

Remington’s replacement solution and filter

is model #CC-100. U.S. residents:

To order, contact us at (800) 736-4648,

www.remington-products.com, or visit

your local retailer.

Canadian residents: For shaver accessories,

call (800) 268-6531 or write: Remington

Products (Canada) Inc., P.O. Box 601, Postal

Station "T," Dept. A-100, 3019 Dufferin St.,

Toronto, Ontario, Canada M6B3T7.

To Charge Your Shaver

Your Smart Shaver can also be recharged

by plugging it into the cord directly.

■ Use only the charging adapter supplied

with the shaver.

■ Make sure your shaver is turned off.

■ Connect the cord to the shaver, then

plug the charging adapter into the elec-

trical outlet. A charging indicator light

will come on.

■ Your shaver cannot be overcharged, so

you can leave it plugged in and charg-

ing between shaves.

■ To preserve the life of the batteries, let

them fully run out every six months,

then recharge them for a full 24 hours.

■ Cord/cordless rechargeable shavers

can run directly off the cord if neces-

sary. They will not recharge while you

are shaving, so after shaving with the

cord, turn the unit off and set it aside to

charge. Cord/cordless shavers should

not be used strictly as cord-operated

shavers, as continued cord-only use

will result in reduction of battery life.

■ Quick Charge provides up to three

weeks of shaving after a one-hour

charge, or a single shave after a

five-minutes charge.

NOTE: If your shaver battery is completely

discharged or the shaver has not been

used for a long time, the shaver may not

start when operated using the cord. If this

happens, charge the shaver for approxi-

mately five minutes before shaving.

1 2 3 4 5 6 7 8 9 10 ... 24 25

Comments to this Manuals

No comments

Remington R-9500 User Manual Page 5

Comments to this Manuals

Related products and manuals for Electric Shavers Remington R-9500