Remington RM5520R Operator's Manual download pdf (Page 2)

SAFETY INFORMATION

• SAFETY AND INTERNATIONAL SYMBOLS •

This operator's manual describes safety and international symbols and pictographs that may appear

on this product. Read the operator's manual for complete safety, assembly, operating, maintenance

and repair information.

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in conjunction with other symbols

or pictographs.

• READ OPERATOR'S MANUAL

WARNING:

Read the operator’s manual(s) and follow all warnings and

safety instructions. Failure to do so can result in serious injury to the operator and/or

bystanders.

• WEAR HEAD, EYE AND HEARING PROTECTION

WARNING:

Thrown objects and loud noise can cause severe eye injury

and hearing loss. Wear eye protection meeting ANSI Z87.1-1989 standards and ear

protection when operating this unit. Wear head protection when operating this unit;

falling objects can cause severe head injury. Use a full face shield when needed.

• KEEP BYSTANDERS AWAY

WARNING:Keep all bystanders, especially children and pets, at least 50

feet (15 m) from the operating area. If anyone enters the work area, stop the unit!

SYMBOL MEANING

• WEAR SAFETY FOOTWEAR

Wear non-slip safety footwear when using this equipment.

• WEAR SAFETY GLOVES

Wear non-slip, heavy-duty protective gloves when handling the unit.

• KICKBACK WARNING

Contact of the guide bar tip with any object should be avoided. Tip contact may cause

the guide bar to move suddenly upward and backward, which may cause serious injury.

• DO NOT install a bow guide on this unit. Bow guides have a larger kickback zone, which increases the

chance of kickback and serious injury. This increased risk is not significantly reduced by using a low

kickback saw chain. Using a bow guide on this unit is extremely dangerous.

• Never start the saw when the guide bar is inside an existing cut. Be extremely careful when re-entering

a cut.

• Keep proper footing and balance at all times.

• Always begin a cut with the engine running at full speed. Fully squeeze the throttle control trigger

and maintain a steady cutting speed. Slower speeds increase the chance of kickback. Keep the

saw housing pressed firmly against the wood.

• Watch for shifting logs, branches, or other objects that might pinch, or fall onto, the chain while cutting.

• If using wedges, only use wedges made of plastic or wood. Do not use metal to hold a cut open.

• Follow the manufacturer’s sharpening and maintenance instructions for the saw chain.

• Only use replacement guide bars and chains specified by the manufacturer or the equivalent. These

are available from authorized service dealers. Use of any unauthorized parts or accessories could

lead to serious injury to the operator or damage to the unit and will void the warranty.

• Use devices, such as low-kickback chains, guide bar nose guards, chain brakes and special guide

bars, which reduce the risks associated with kickback. There are no other replacement

components for achieving kickback protection in accordance with CSA Z62.3.

• Low-kickback saw chain is chain that has met the kickback performance requirements of ANSI

B175.1-1991 and is in accordance with CSA Z62.3. Do not use a replacement chain unless it has

met these requirements for the specific model. As saw chains are sharpened, some of the low

kickback qualities are lost and extra caution should be used.

GENERAL SAFETY PRECAUTIONS

• DO NOT handle the unit with wet hands.

• DO NOT

operate a

chain

saw in a tree or on a ladder unless specifically trained to do so.

• DO NOT use the unit in the presence of flammable liquids or gases.

• DO NOT operate a unit that is damaged, improperly adjusted or not completely and securely

assembled. Be sure that the saw chain stops moving when the throttle control trigger is released.

Do not use the unit if the stop switch does not turn the unit on and off properly or if the lockout

switch does not work. Have defective switches replaced by an authorized service center.

• DO NOT attempt operations beyond the operator’s capacity or experience.

• DO NOT cut near electrical cables or power lines.

• DO NOT force the chain saw, especially near the end of a cut. It will do a better, safer job when

used at the intended rate.

• DO NOT touch the engine or muffler. These parts can become extremely hot during operation and

remain hot for a short time after the unit is turned off.

•

To reduce the risk of fire, keep the engine and muffler free from debris, excessive grease and carbon

build up.

•

Before cutting, always inspect wood for foreign objects that could cause injury to the operator or

damage to the unit. Never cut through nails, metal rods, railroad ties or pallets. If a foreign object is

struck, stop the unit and inspect it for damage.

• Keep all body parts away from the saw chain when the engine is running. Before starting the saw,

make sure the saw chain is not contacting anything.

• Always stop the engine when operation is delayed, before setting down the unit or when walking

from one location to another. Make sure the chain comes to a complete stop. Do not leave the unit

unattended while the engine is running. Always stop the engine when not in use.

•

To avoid accidental starting, never carry the unit with fingers on the throttle control trigger. Only pull the

starter rope when in the starting position. The operator and unit must be in a stable position while

starting the engine. Refer to Starting and Stopping Instructions.

•

Always carry the chain saw by the front handle with the engine off, finger off the throttle control trigger, the

muffler positioned away from the body and the guide bar and saw chain sheathed in the scabbard and

positioned to the rear.

•

Always make sure the stop switch is in the proper position before starting or stopping the engine.

•

When cutting a limb that is under tension, be alert for spring back, which may cause the operator to

be struck when the tension of the wood fibers is released.

• Use extreme caution when cutting small-sized brush and saplings, as slender material may catch

the saw chain and be whipped toward the operator or pull the operator off balance.

•

This saw is classified by UL as a Class 1C saw

in accordance with CSA Z62.1-03

. It is intended for

infrequent use by homeowners, cottagers and campers, and for general applications such as

clearing, pruning, cutting firewood, etc. It is not intended for prolonged use. If the intended use

involves prolonged periods of operation, this may cause circulatory problems in the user’s hands due

to vibration.

GASOLINE SAFETY

• DO NOT smoke while handling fuel or while operating the unit.

• Always keep a fire extinguisher nearby while operating the unit.

• Store fuel only in containers specifically designed and approved for the storage of such materials.

• Always stop the engine and allow it to cool before filling the fuel tank. Never remove the fuel tank

cap or add fuel when the engine is hot. Always loosen the fuel tank cap slowly to relieve any

pressure in the tank before fueling. Do not smoke.

• Always mix and add fuel in a clean, well-ventilated outdoor area where there are no sparks or

flames. Do not smoke.

• Never operate the unit without the fuel cap securely in place.

• Avoid creating a source of ignition for spilled fuel. Wipe up any spilled fuel from the unit

immediately before starting the unit. Move the unit at least 30 feet (9.1 m) from the fueling source

and site before starting the engine. Do not smoke.

• Never start or run the unit inside a closed room or building. Breathing exhaust fumes can kill.

Operate this unit only in a well-ventilated outdoor area.

• Always store the unit and fuel in a cool, dry and well-ventilated space where fuel vapors cannot

reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Never

store the unit, with fuel in the tank, inside a building where fumes may reach an open flame or spark.

MAINTENANCE AND STORAGE SAFETY

• If the unit is not working as it should, has been dropped, damaged, left outdoors or dropped into

water, do not use the unit. Have the unit serviced by an authorized service center.

• All

service

, other than the

maintenance

procedures described in this manual, should be performed

by an authorized service center.

• Follow all maintenance instructions in this manual.

• Before inspecting, servicing, cleaning, storing, transporting or replacing any parts on the unit:

1. Stop the engine. Make sure the stop switch is in the STOP position and the throttle control trigger

is released.

Make sure all moving parts have stopped.

3. Allow the unit to cool.

Make sure the

chain brake is disengaged.

• Never remove, modify or make inoperative any safety device furnished with the unit.

• For safer, more effective performance, make sure the guide bar and chain are properly cleaned,

lubricated, tightened and sharpened. Check the guide bar and chain at frequent intervals for proper

adjustment.

• Frequently inspect the unit for damage.

Before further use, any damaged part should be carefully

checked to determine that it will operate properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts, breakage of parts, fuel leaks and any other

conditions that may affect its operation. Damaged parts should be properly repaired or replaced by

an authorized service center, unless otherwise indicated in this manual.

• Use only original manufacturer replacement parts and accessories, which are designed specifically to

enhance the performance and maximize the safe operation of the product. Failure to do so may cause

poor performance and possible injury. Use only the chain and guide bar supplied with this product.

• Be sure to secure the unit while transporting.

• Always use the scabbard on the guide bar and saw chain during transportation and storage.

• When not in use, store the unit in a locked-up and dry, or high and dry, place to prevent

unauthorized use or damage. Keep out of the reach of children.

•

Keep the handles dry, clean and free from debris, oil, fuel and grease. Clean the unit after each use.

Never douse or spray the unit with water or any other liquid.

Do not use solvents or strong detergents.

• USE BOTH HANDS

Always use both hands while operating the chain saw. Never use only one hand to

operate the unit.

• PRIMER BULB

Push primer bulb, fully and slowly, 10 times.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel

• OIL

Refer to operator’s manual for the proper type of oil.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF or STOP

• DO NOT USE E85 FUEL IN THIS UNIT

WARNING:It has been proven that fuel containing greater than 10%

ethanol will likely damage this engine and void the warranty.

WARNING:Use caution when handling fuel. Gasoline is highly flammable,

and its vapors can explode if ignited. Take the following precautions:

SAVE THESE INSTRUCTIONS

• CHOKE CONTROL

1. • FULL choke position

2. • RUN position

1 2 3 4 5 6 7 ... 23 24

Comments to this Manuals

No comments

Remington RM5520R Operator's Manual Page 2

Comments to this Manuals

Related products and manuals for Power chainsaws Remington RM5520R