Remington i-LIGHT PRO Operations Instructions download pdf (Page 10)

1918

•

 Donottakehotbaths,showers,orusesteamroomsandsaunasfor24hours

after treatment.

• Donotswimfor24hoursaftertreatment.

• Donottakepartincontactsportsfor24hoursaftertreatment.  

 Donotwear

clothingoverthetreatedarea.   

 Donotdepilate(waxing,plucking,threadingorcreams)duringthetreatment–shavingis

acceptable as long as you avoid shaving 24 hours after each treatment.

 Donotusebleachingcreamsorperfumedproductsfor24hoursaftertreatment. 

 Donotscratchorpickatthetreatedarea.



CLEANING YOUR I-LIGHT DEVICE

✹ CAUTION: Before cleaning your i-Light device, make sure that the power switch is OFF and

the power cord is disconnected from the base unit.

 Regularcleaninghelpstoensureoptimalresultsandalonglifeforthei-Lightdevice.The

exterior surface of the base unit and hand piece may be wiped clean with a slightly

damp cloth.

• TocleantheFlashWindow,useonlythelint-freeclothincludedwithyouri-Lightdevice.

Take care not to scratch or chip the Flash Window. Scratches and chips can reduce the

oftheunit.

• Forstubbornstains,useadampenedcottonswabtoapplyasmallamountofwatertothe

Flash Window and clean with the lint-free cloth provided.

• Useasmallhand-heldvacuumtoremovedustanddebrisfromthehandpiecevents

✹ WARNING: If the Flash Window is cracked or broken, the unit must not be used. Never

scratch the ﬁlter glass or the metallic surface inside the Treatment Head.

✹ CAUTION: The i-Light device is a high voltage device. Never immerse in water. Never clean

the unit or any of its parts under a tap or in a dishwasher.

Donotusepetroleum-basedor cleaningagentsbecauseoftheriskof Never

use scouring pads, abrasive cleaning agents or aggressive liquids such as oil or acetone to

clean the unit.



TROUBLESHOOTING / STORAGE / MAINTENANCE

✹ I-Light Device Maintenance

✹ CAUTION: Before performing maintenance on your i-Light device, ensure that the power

switch is OFF and the power cord is disconnected from the base unit.

✹ Replacing the Bulb

1. Press the treatment head release buttons and gently pull to remove the treatment head.

2. Gently pull out the old bulb cartridge.

3. Replace with a new bulb cartridge.

✹ CAUTION:Whenreplacingthebulbcartridge,donottouchthe bulbsdirectlyasthis

 leavesoilsandresidue.Doingsocouldreducethe

ofthebulbsorcause

them to crack during treatment.

4. Replace the treatment head, making sure it snaps into place.

✹ Storage

• Switch theunit,unplugitandletitcooldownfor10minutesbeforestorage. 

• Storetheunitinadryplaceatatemperaturebetween15ºCand35ºC.

✹ Troubleshooting

Always read these instructions fully before using the i-Light device.

Refer to this troubleshooting guide if you experience any problems with your i-Light device,

as this section addresses the most common problems you could encounter.

If you have followed the instructions in this section and continue to experience problems,

please contact the Remington™ Service Centre for further assistance.

The power switch is ON, but the unit is not working.

• Makesuretheunitispluggedintoaworkingelectricaloutlet.  

• Tryswitchingtoa

outlet.    

The unit appears to have cracks or is broken.

Do not use if the unit is damaged. If you have concerns about using the unit, discontinue use

and contact the Remington™ Service Centre for further assistance.

•



™

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Remington i-LIGHT PRO Operations Instructions Page 10

Comments to this Manuals