Remington R300 Owner's Manual download pdf (Page 6)

barrel ring over the magazine tube. See

Picture 7.

7. Once the barrel is fully inserted into the

receiver, replace the magazine cap on top

of the magazine tube. Tighten by turning

clockwise until hand-tight.

8. Point the firearm in a safe direction.

9. Open the bolt by pressing the bolt release

while moving the fore-end fully rearward.

TO LOAD THE FIREARM:

WARNING! The specific gauge and length of

shotshell ammunition suitable for use in your

shotgun is marked on the barrel. Different

gauges and shell lengths are not interchange-

able. Do not use any ammunition other than

the designated gauge and length specified for

your shotgun. USING INCORRECT AMMUNI-

TION IN YOUR FIREARM CAN RESULT IN A

SEVERE MALFUNCTION OF YOUR FIREARM

OR AMMUNITION LEADING TO PERSONAL

INJURY OR DEATH. See the Ten

Commandments of Firearm Safety on page 2.

Ammunition:

Always check the shotshell for the correct

gauge and length before loading the firearm.

To find additional information on shotshells

ammunition, see publication: The Remington

Guide to Shotguns and Ammunition at

www.remington.com.

To load the Chamber and

Magazine:

NOTE: The bore should be cleaned before

loading the firearm the first time.

Follow cleaning instructions shown on Page

14, “To Clean Barrel”.

1. Point the shotgun in a safe direction.

2. Engage the safety by placing the safety

mechanism in the "ON" or "SAFE" posi-

tion. The Red Band Will NOT Be Visible.

3. While pressing the bolt release, open the

action by pulling the fore-end rearward.

4. Look into the ejection port, visually check

the chamber, loading port, and magazine

to make sure the shotgun is completely

unloaded. Also make sure the barrel is

free of obstructions.

To Load the Chamber:

5. Put one shell of correct gauge and length

through the ejection port.

6. Move the fore-end forward, closing the

action.

To Load the Magazine:

7. Push up to four (4) shells, (three (3) 3-

1/2”) one at a time, fully forward into the

magazine tube making sure the rim of

each shell engages the feed latch and is

held inside the magazine tube.

WARNING! The shotgun is now cocked and

fully loaded. Make sure the safety mecha-

nism is still engaged in the “ON” or “SAFE”

position. The Red Band Marking Will NOT be

Visible. Keep the shotgun pointed in a safe

direction.

To Load The Chamber From The

Magazine:

1. Point the firearm in a safe direction.

2. Engage the safety by placing the safety

mechanism in the “ON” or “SAFE" posi-

tion. The Red Band Will NOT Be Visible.

3. With the bolt open, visually check the

chamber, ejection port, carrier, and mag-

azine making sure the shotgun is com-

pletely unloaded and the barrel is free of

obstructions.

4. Close action by moving the fore-end fully

forward.

5. Push up to four (4) shells, (three (3) 3-

1/2") one at a time, fully forward into the

magazine tube making sure the rim of

each shell engages the feed latch and is

held inside the magazine tube.

6. Open the bolt by pressing the bolt release

while moving the fore-end fully rearward.

7. Place the shell in the chamber by closing

the bolt and moving the fore-end fully

forward until the bolt locks into position.

WARNING! The shotgun is now cocked and

fully loaded.

TO DISCHARGE THE FIREARM:

1. Point the muzzle at your intended target.

2. Disengage the safety mechanism by

moving the safety button to the "OFF" or

"FIRE" position. The Red Band Will Be

Visible.

3. With the butt of the shotgun firmly

mounted against your shoulder and tar-

get acquired, pull the trigger. The firearm

will discharge each time the trigger is

pulled and the action is cycled until the

magazine and chamber are empty.

4. Engage the safety mechanism by placing

the safety button in the "ON" or "SAFE"

position. The Red Band Will NOT Be

Visible.

5. Look into the ejection port, visually check

the chamber, loading port, and magazine

to make sure the shotgun is completely

unloaded.

HOW TO UNLOAD THE

FIREARM

To Unload By Using Pump Action:

WARNING! NEVER assume your shotgun is

unloaded to justify careless handling. Always

control the direction of the muzzle of your

firearm, even if you think it is completely

unloaded.

1. Keep the shotgun pointed in a safe direc-

tion throughout the unloading process.

2. Engage the safety by placing the safety

mechanism in the "ON" or "SAFE" posi-

tion. The Red Band Will NOT Be Visible.

3. Open the bolt by pressing the bolt release

while moving the fore-end slowly rear-

ward until the shell clears the chamber.

4. Lift the front of the shell outward and

remove from ejection port.

5. Continue to move the fore-end fully rear-

ward until the next shell is released from

the magazine onto the carrier.

6. Tip the firearm sideways allowing the

shell to drop from the ejection port.

7. Close the action by moving the fore-end

forward.

8. Repeat opening and closing the action

(steps 5 through 7) until all shells are

removed from firearm.

9. With the bolt open, visually check the

chamber, carrier, and magazine making

sure the shotgun is completely unloaded.

To Unload Magazine Manually:

1. Keep the shotgun pointed in a safe direc-

tion throughout the unloading process.

2. Engage the safety by placing the safety

mechanism in the "ON" or "SAFE" posi-

tion. The Red Band Will NOT Be Visible.

3. With action closed, push the carrier up

against the bolt carrier exposing the staged

shell in the magazine.

WARNING! Shells in Magazine are under

spring compression. Wear eye protection

to avoid possible serious personal injury.

4. Push the left (feed) latch in toward the

receiver wall until the stage shell is

released from the magazine. See

Picture 9.

5. Repeat step 4 until all shells are removed

from magazine and the orange follower

can be seen.

6. Look into the ejection port and visually

check the chamber, carrier, and magazine

to make sure the firearm is completely

unloaded and free of obstructions.

To Change the Choke Tube:

WARNING! COMPLETELY UNLOAD the

firearm before changing the choke tube.

(See Unloading Instructions).

1. Point the shotgun in a safe direction.

2. Engage the safety by placing the safety

mechanism in the "ON" or "SAFE" posi-

tion. The Red Band Will NOT Be Visible.

3. Open the bolt by pressing the bolt release

while moving the fore-end fully rearward.

4. With the bolt open, look into the ejection

port and visually check the chamber, car-

rier, and magazine to make sure the

firearm is completely unloaded. Change

the choke tube only when the bolt or

action is open.

PICTURE 9

Left Latch

Shot Shell

PICTURE 7

Barrel

Barrel Ring

Magazine Tube

PICTURE 8

SHOTGUN SHELL

Gauge Marking

Head

Body &

Load Marking

Rim

Primer

e5762remington_Q6.qxp 9/25/09 11:06 AM Page 6

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Remington R300 Owner's Manual Page 6

Comments to this Manuals

Related products and manuals for Power screwdrivers Remington R300