Remington R-845 User Manual download pdf (Page 3)

Easy-View

Trimmer

Button

Brush

Storage Pouch

(Models R-835,R-842 and R-845 only)

Plastic

Headguard

Head & Cutter

Assembly

Charging

Indicator

(Green) Models

R-842 and R-845

On/Off Button

Locking Bar

Models R-842

and R-845

MODEL R-845/R-842 Cordless Rechargeable

Operation with charging indicator,Worldwide voltage 100-240

volts,A.C.,50-60 Hz

MODEL R-835/R-830 Corded Operation

Single voltage 120 volts,A.C.,60 Hz Note:Model R-830 has

no storage pouch.

All worldwide voltage models have automatic voltage

conversion Shaver will automatically adjust to any worldwide

A.C.voltage between 100 and 240 volts,A.C.,50-60 Hz.Do not

connect to direct current “D.C. Voltage”.

To Charg e

Models R-842 and R-845

have a red low-battery indicator to show

when shaver needs recharging.This also indicates approximately 5

to 6 minutes of shaving time left when indicator first comes on.

Prior to using your shaver for the first time,put it on charge for 24

hours.To charge your shaver:

• Slide the On/Off Button to the “Off” position.

• Connect the cord to the shaver and then to the electric outlet.

The Charging Indicator light will glow green,indicating your

shaver is charging.

• Your shaver cannot be overcharged,so you can leave it plugged

in and charging between shaves.

•

Use only the cord supplied with shav e r.The R-842 and R-845 are

designed for cordless operation only.P l u gging in the cord will not

provide the power to shav e .

Corded Operation

Connect cord to shaver and then to electrical outlet.Make sure

shaver is turned off before plugging cord into outlet.

Battery Removal

(Corded/Cordless and Cordless Rechargeable Models Only)

When your rechargeable shaver reaches the end of its useful life,the batteries

must be removed from the shaver and be recycled or disposed

of properly in accordance with your local and state requirements.

The following procedures should be followed

for battery removal:

• Make sure your shaver is unplugged

from any outlets,so you don’t risk an electrical shock.

• Remove the Head Assembly by gently lifting the

assembly away from the shaver.

• Using a small Phillips head screwdriver,remove

the screws from the upper and lower back of

the shaver.

• Pull or gently pry the the shaver halves apart,

exposing the battery.

• Hold each battery in place and very carefully

slide the clips from the terminals on each battery.

• Lift or pry the battery out of the shaver.

CAUTION:THESE NICKEL-CADMIUM BATTERIES

MUST BE RECYCLED OR DISPOSED IN ACCOR-

DANCE WITH STATE AND LOCAL REGULATIONS.

Do not burn or mutilate,as they may burst or

release toxic materials.Do not short circuit,as it

may cause burns.

The EPA certified RBRC

B at t e ry Recycling Seal on the nickel-cadmium

(Ni-Cd) battery indicates Remington Products Company, L.L.C.is

voluntarily participating in an industry program to collect and recycle

these batteries at the end of their useful life,when taken out of service

in the United States or Canada.The RBRC

program provides a

convenient alternative to placing used Ni-Cd batteries into the trash

or the municipal waste stream,which may be illegal in your area.

Please call 1-800-8-BATTERY

for information on Ni-Cd battery

recycling and disposal bans/restriction in your area.Remington

Products Company, L.L.C.’s involvement in this program is part of

our commitment to preserving our environment and conserving our

natural resources.

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

Remington R-845 User Manual Page 3

Comments to this Manuals

Related products and manuals for Electric Shavers Remington R-845