Remington WDF-1600 User Manual download pdf (Page 5)

3. Use a Phillips head screwdriver to

remove the 4 screws that hold the

head assembly in place.

4. Lift the head assembly out of the shaver

by grasping the cutter and trimmer

drivers, lining them up in the central

position and pulling. Discard.

5. Remove the next 4 screws, so you can

lift the shaver’s upper outer shell off the

shaver and discard it.

6. Remove the two

screws

(located opposite

of the batteries)

holding the lower

housing. Remove

the lower

housing.

7. Cut the tape

holding the

batteries

to the inner

frame assembly,

and discard it.

8. Cut the 2 metal

tabs connecting

the batteries to

the inner frame.

9. Pull the batteries

free from the

inner frame and dispose of

properly.

Storage

While storing the product never wrap cord

around the product. Overtime the cord may

become worn and break.

Seek an authorized service representative

if the appliance requires more than

rountine cleaning and maintenance.

Cleaning Your Shaver

Remington recommends cleaning your

shaver after every use for optimal

performance.

1. Turn the shaver OFF.

2. Press the side release

button to flip open the

head assembly.

3. Screens-Do not use the

brush to clean the

screens. Instead, blow the

shavings out or rinse the

screens under cold or

warm water.

4. Cutters and trimmer-

Use the cleaning brush

to sweep any loose hairs

from the cutters and

trimmers, or rinse/dunk

them in cold or warm

water. Do NOT use hot

water.

5. After cleaning, return the

foils and head assembly

to their original position

on the shaver.

6. If the shaver was rinsed

with water, or if you used

it in the shower, hold it

facing downward into the

sink, and turn it on for a

few seconds to dispel

additional water.A gentle

shake will also help.

7. To clean the external surfaces of the

shaver, use a damp cloth. Do NOT use

strong detergents or other chemicals.

8. To dry, wipe the surface of the overall

shaver with a dry towel. Do NOT use a

hairdryer or heater to dry the shaver.

Cleaning & Maintenance

Replacing Cutters And

Screens

When is it time to replace your screens

and cutters?

The cutters and screens of your shaver

will wear with use and eventually require

replacement to maintain a close,comfort-

able shave. It is very important to replace

your screens and cutters when necessary

to ensure a close,comfortable shave

without irritation.

Depending on your shaving technique

and habits, the screens will usually last 6

months; the cutters, 12 months. If you are

replacing the cutters it’s a good idea to

replace the screens at the same time.

Here are some signs that you screens and

cutters need replacing:

Irritation: As screens get worn, you may

notice that your skin feels more sensitive

after a shave.

Pulling: As cutters wear, your shave may

not feel as close and you may feel your

shaver is “pulling”the hairs.

Wear-through: You may notice that the

cutters have worn through the screens.

To prevent inadvertent damage to the

cutters and screens, do not attempt to

remove them from the head assembly

unless you are replacing them. Removal

instructions are included with the cutter and

screen replacement packages.

The replacement part for the WDF-1200

& 1600 is model SP-130 & SP-132.

U.S. residents:

To order shaver accessories call

800.736.4648, visit

www.remington-products.com

or visit you local retailer.

To replace a cutter assembly that is

removed unintentionally:

1. Hold the cutter in the middle. The blades

will not cut your fingers, so no special

handling techniques are necessary.

2. Align the cutter so the little bar on the

bottom meets the opening in the clip.

3. Press down on the center of the cutter

until it snaps into place. Do not push

down on the ends of the cutter, as you

may bend the cutter, reducing its ability

to cut cleanly.

4. Do not separate the cutter’s blades from

the plastic pieces they are attached to,

as this may damage the assembly.

Rechargeable Battery

Removal

When your WDF-1600 reaches the end

of its useful life, the batteries must be

removed from the shaver and be recycled

or disposed of properly in accordance with

your state and local requirements. If this

is not required by law,you may elect to

dispose of the shaver without the batteries.

Make sure shaver is unplugged before you

begin, to avoid possible electric shock

hazard.

CAUTION: DO NOT PUT IN FIRE OR MUTI-

LATE YOUR BATTERIES WHEN DISPOSING

AS THEY MAY BURST AND RELEASE TOXIC

MATERIALS. DO NOT SHORT CIRCUIT AS IT

MAY CAUSE BURNS. DISPOSE PROPERLY

IN ACCORDANCE WITH YOUR LOCAL AND

STATE REQUIREMENTS.

How to Remove the Rechargable Battery:

1. Press the head release button to open

the shaver’s head assembly.

2. Pull the cutters off the cutter drives

that hold them.

CS27354_WDF_1200/1600_IB.QXD 1/19/06 2:12 PM Page 8

1 2 3 4 5 6 7

Comments to this Manuals

No comments

Remington WDF-1600 User Manual Page 5

Comments to this Manuals

Related products and manuals for Electric Shavers Remington WDF-1600