Remington BHT-2000 User Manual download pdf (Page 4)

Charging the BHT-2000

Before using the for the first time, it must

charge for 14-16 hours.

1. Make sure the groomer is turned off.

2. Connect the cord to the unit, then plug

the charging adapter into the electrical

outlet.A charging indicator will light up.

3. Your groomer cannot be over charged so

you can leave it plugged in and charged

between uses, but if the unit is not going

to be used for an extended period of

time (2-3 months) unplug it and fully

recharged when you want to use it

again.

4. Only use the charging adapter supplied

with the unit.

5. Charging should be done at temperature

between 4ºC and 35ºC, or it could

decrease the battery’s life.

6. To preserve the life of the batteries, let

them run out every 6 months, than

recharge them for 24 hours.

7. This product is intended for cordless use

only.

Before using your groomer: The High

Precision Body Hair Trimmer Shaver is

washable so it can be used in the shower

or rinsed under water during cleaning.

Therefore, to maintain the performance of

the cutters, oil before each use and after

rinsing.Turn the trimmer on to distribute

the oil evenly. Prior to using,wipe off any

excess oil. Be sure that the groomer is

truned off when applying the oil.

Take a moment

Be patient when first using your BHT-2000.

As with any new product, it may take a

little while to familiarize yourself with it,

especially if you are using a trimmer for all

the first time or are using a different brand.

■ Remove the cutting assembly by firmly

pushing up on the blade with your

thumb.The cutting assembly rests on

a gentle spring. Use your other hand to

cover the cutting assembly to prevent

accidents.

Removing the shaver attachment

■ Ensure the trimmer is off.

■ Hold the trimmer in one hand with your

thumb firmly on the thumb wheel to

keep it from turning.

■ With your other hand, gently pull the

shaver attachment off the trimmer.

Removing the shaver cover

■ Ensure the trimmer is off.

■ Gently push the buttons either side of

the shaving foil.With the other hand lift

the shaver cover. Clean then replace.

Replacing the cutter assembly

■ Ensure the trimmer is off.

■ Hold the trimmer in one hand.With your

other hand, insert the

lower part of the cut-

ter assembly into the

trimmer, push down

the cutter until firmly

attached.

Replacing the trimmer comb and shaver

attachment

■ Hold the trimmer in one hand with your

thumb firmly on the thumb wheel to

keep it from turning. Ensure that the

length position indicator is at 1.

■ Slide the comb/shaver down the

grooves until it clicks into place.

! The trimmer comb and shaver attachment

can only be attached in one way. If it does

not go on correctly, turn it around and try

again.

How to Use

Take the time to acquaint yourself with your

new trimmer, as we are confident you will

receive years of enjoyable use and

complete satisfaction.

Trimming

■ Use the thumb wheel to set the trimmer

comb to the desired length setting. It’s

a good idea to begin trimming at one

of the longest settings (4 or 5) to avoid

accidentally trimming hair too short.As

you become familiar with the settings,

you can then select your desired length

setting.

■ Turn the unit on.

■ Place the flat top of the trimmer comb

against the skin.

■ If hair builds up in the trimmer comb

during the trimming process, switch the

unit off, pull off the adjustable trimmer

comb and brush/rinse it off.

■ For an even closer look and precise

shaping, remove the adjustable trimmer

comb and trim the hairs along the outer

edge.

■ When you are finished, turn the trimmer

off, clean it, and return it to its storage

pouch.

Adjusting the trim length

The trimmer comb can be adjusted to give

you 5 different trim lengths simply by by

turning the thrmb wheel to the desired

setting.Turn the thumb wheel clockwise

for a shorter length, counter-clockwise for

longer length.The wheel will click into

place as it reaches each setting, and the

setting number will appear on the length

position indicator. Here’s what the length

settings mean:

Setting Length

1 3mm

2 5mm

3 7mm

4 8mm

5 12mm

! Trimmer comb must be attached to the

trimmer in order to use the hair length

selector.

Edging and shaping

■ Remove the trimmer comb attachment.

■ Hold the trimmer at a right angle to

your skin and press down gently.

■ Edge and shape the area as desired.

Using the shaver attachment

■ Hold the shaving head to your skin.

■ Stretch your skin with your free hand so

hairs stand upright.

■ Only apply light pressure on the shaving

head while shaving.

■ Shave against hair growth.

! The Microscreen shaving technology with

circular foil holes is developed to give a

controlled close cut.

Removing the trimmer comb and cutting

assembly

■ Be sure trimmer is off.

The trimmer comb

may be on any setting.

■ Hold the trimmer in

one hand with your

thumb firmly on the

thumb wheel to keep

it from turning.

■ With your other hand,

gently pull the trimmer

comb attachment off

the trimmer.

CS27555_BHT2000_IB 8/31/05 5:14 PM Page 6

1 2 3 4 5 6 7 8 9 ... 12 13

Comments to this Manuals

No comments

Remington BHT-2000 User Manual Page 4

Comments to this Manuals

Related products and manuals for Electric Shavers Remington BHT-2000