Remington 106821 User Manual download pdf (Page 15)

108540 www.desatech.com

OPERATING CHAIN SAW

EXTENSION CORDS

Use proper extension cords with this Pole Saw. Use

only extension cords marked for outdoor use. The cord

must be marked with sufﬁx W or W-A following the

cord type designation.

Example:

SJTW-A or SJTW.

Use proper sized cord with this saw. Cord must be heavy

enough to carry current needed. An undersized cord

will cause voltage drop at saw. Saw will lose power and

overheat. Follow cord size requirements listed below.

WARNING: Read and understand this

owner’s manual before operating this Pole

Saw. Make certain you read and under-

stand all

Important Safety Information,

pages 2 through 4. Improper use of this

Pole Saw can cause severe injury or death

from ﬁre, electrical shock, or body contact

with moving chain, or falling wood.

Cord Length AWG Cord Size

25 feet 16 AWG

50 feet 16 AWG

100 feet 16 AWG

150 feet 14 AWG

Keep cord away from cutting area. Make sure cord

does not catch on branches or logs during cutting.

Inspect cords often. Replace damaged cords.

The extension cord may come undone from the power

cord during use. To avoid this, make a knot with the

two cords as shown in Figure 7.

ADJUSTING POLE LENGTH

The Remington Pole Saw has a telescoping pole as-

sembly that will extend from 57 inches (fully re-

tracted) to 96 inches (fully extended). A threaded

compression coupling is used to hold the pole in

position at any extended length.

1. To extend the pole, loosen coupling by turning

coupling nut counterclockwise as shown in Fig-

ure 8. Pole will slide freely.

2. Pull inner pole section out to desired length of

extension.

Note:

Only extend pole to minimum

length required to reach limb that is being cut.

3. To lock pole in position, tighten coupling by turning

coupling nut clockwise (see Figure 8) until firmly

hand tight. Make sure saw handle is aligned with

pole handle before tightening coupling nut.

IMPOR-

TANT:

Do not use wrench or pliers to overtighten

coupling. Damage to coupling or pole may result.

OILING CHAIN

Always check oil level before using saw. Do not attempt

to operate the oil system while saw is in operation. To oil

chain, press squeeze bulb. Oil will feed onto the guide

bar and chain. Press squeeze bulb at least once before

each cut. Check oil level often by looking at oil sight

level hole. Oil sight level hole is on left side of saw, be-

tween front handle and front hand guard.

CUTTING WITH THE POLE SAW

1. Connect saw to extension cord. Connect exten-

sion cord to power supply.

2. Use both hands to grip Pole Saw. Use only des-

ignated grip areas when operating Pole Saw (see

Figure 9). Use firm grip. Thumbs and fingers

must wrap around Pole Saw handle and pole.

3. Make sure your footing is ﬁrm. Keep feet apart.

Divide your weight evenly on both feet.

4. When ready to make a cut, press in trigger switch

lock-out and squeeze trigger switch (see Figure

10). This will turn Pole Saw on. Releasing trig-

ger switch will turn Pole Saw off. Make sure saw

is running at full speed before starting a cut.

5. When starting a cut, place moving chain against

wood. Hold Pole Saw firmly in place to avoid

possible bouncing or skating (sideways move-

ment) of saw.

6. Guide Pole Saw using light pressure. Do not force

Pole Saw. The motor will overload and can burn

out. It will do the job better and safer at the rate

for which it was intended.

7. Remove Pole Saw from a cut with saw running at

full speed. Stop Pole Saw by releasing trigger. Make

sure chain has stopped before setting Pole Saw down.

ASSEMBLY OF POLE SAW

1. Slip handle bracket over chain saw

handle from

the right side (see Figure 5).

Note:

The trigger

must be depressed before the bracket will go onto

the handle.

Push the lockout button and depress the trigger.

While holding the trigger in, place the trigger

support portion of the bracket under the trigger

and slide the bracket onto the chain saw handle.

The bracket will keep the trigger in the “on”

position.

2. Align holes in pole bracket with holes in handle

bracket. Install Phillips head screws with

lockwashers through pole bracket from left side

and thread into the weld nuts on the handle

bracket. Tighten screws securely by hand.

3. Plug the saw power cord into receptacle cord at

end of inner pole.

ASSEMBLY

Continued

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Comments to this Manuals

No comments

Remington 106821 User Manual Page 15

Comments to this Manuals