Remington HH-215T-KFA User Manual download pdf (Page 15)

Troubleshooting Guide

Pinnacle Products International, Inc. Kerosene User’s Manual Page 15

Problem

Possible Cause Solution

Heater fires, but Main PCB shuts

heater off after a short period of time.

Lamp is flickering, and LED display

shows “E1”.

1. Incorrect pump pressure

2. Dirty Input, Output or Lint Filter

3. Dirty Fuel Filter

4. Nozzle is Dirty

5. Photocell lens is Dirty

6. Photocell not installed properly

7. Photocell Defective

8. Improper electrical connection between

Main PCB and Photocell.

1. Adjust Pump Pressure (Page 11)

2. Clean/replace Air Filter (Page 9)

3. Clean/replace Fuel Filter (Page 10)

4. Clean/replace Nozzle (Page 9)

5. Clean/replace Photocell (Page 10)

6. Adjust Photocell position (Page 10)

7. Replace Photocell (Page 10)

8. Check wiring connections (See Wiring

Diagrams, Page 14)

Heater will not operate, or motor runs

for short time. Lamp flickers and LED

display shows “E1”.

1. No kerosene in fuel tank

2. Incorrect pump pressure

3. Corroded Spark Plug or incorrect plug

gap.

4. Dirty Fuel Filter

5. Dirty Nozzle

6. Moisture in Fuel/Fuel Tank

7. Improper electrical connection between

Transformer and Circuit Board

8. Ignitor Wire not connected to Spark

Plug

9. Defective Ignitor

1. Fill tank with fresh kerosene

2. Adjust Pump Pressure (Page 11)

3. Clean/replace Spark Plug (Page 10)

4. Clean/replace Fuel Filter (Page 10)

5. Clean/replace Nozzle (Page 9)

6. Rinse out fuel tank with clean fresh

kerosene (Page 9)

7. Inspect all electrical connections. See

Wiring Diagrams (Page 14)

8. Re-attach Ignitor wire to Spark Plug

(Page 9)

9. Replace Ignitor

Fan does not operate when heater is

plugged in and Power Switch is in the

“ON” position. The lamp is flickering or

on and LED Display shows “E1” or

“E2”.

1. Thermostat is set too low (Does not

apply to HH-45-KFA)

2. Broken electrical connection between

Main PCB and motor

1. Rotate thermostat to a higher setting

2. Inspect all electrical connections. See

Wiring Diagrams (Page 14)

Lamp is flickering, and LED display

shows “E3”

1. Thermostat Switch has failed 1. Replace Thermostat Switch. Wiring

Diagrams (Page 14)

Poor Combustion and / or excess soot

production

1. Dirty Input, Output or Lint Filter

2. Dirty Fuel Filter

3. Poor quality of fuel

4. PSI is too high or too low

1. Clean/replace Air Filter (Page 9)

2. Clean/replace Fuel Filter (Page 10)

3. Be sure fuel is not contaminated or old

4. Use proper pressure (Page 11)

Heater does not turn on and the lamp

is not lit

1. Temperature limit sensor has

overheated

2. No electrical power

3. Fuse Blown

4. Improper electrical connection between

Temperature Limit Sensor and Circuit

Board

1. Push Power Switch to “OFF” and allow

heater to cool for 10 minutes. Push

Power Switch to back to “ON”

2. Check power cord and extension cord

to insure of proper connection. Test

power supply

3. Check/replace Fuse

4. Inspect all electrical connections. Wiring

Diagrams (Page 14)

NEVER LEAVE HEATER

UNATTENDED WHILE BURN-

ING OR WHILE CONNECTED

TO A POWER SOURCE

Kerosene

Forced Air Heaters

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 55 56

Comments to this Manuals

No comments