Remington R-650s User Manual download pdf (Page 6)

11

Cleaning & Maintenance

10

To assure smooth, efficient perfor-

mance, it is important to clean your

shaver. The hand-held unit shall be

detached from the power supply cord

before cleaning. The shaver shall not

be used until it has dried.

The shaver is a

washable shaver,

the hand-held

part of which may

be cleaned under

water.

Daily

Brush inside the head assembly after

each use:

1. Turn the shaver

off.

2. Grip the head

assembly by

the three ridges

and pull it off

the shaver.

3. Use the

cleaning brush

to sweep out

the internal

part of the

head assembly

and the hair

pocket area,

where 3 shaver

spindles are

located.

4. Replace head

assembly.

Weekly

Clean under the cutter assembly at

least once a week:

1. Turn the shaver off.

2. Open the head assembly as above.

3. Unscrew the center screw knob

to remove the cutter retainer

assembly.

4. Use the cleaning brush to sweep

the dust and hairs from under the

cutters.

5. Replace head assembly.

Lubricate

Remington

®

Shaver Saver

®

Lubricant

(SP-4)

lubricates and cleans your

shaver's cutters and head assembly.

The lubricant helps remove hair clip

-

pings while reducing wear. A quick

spray after each shave keeps

your

shaver operating at peak performance.

Cleaning Cautions

■ The construction of this shaver

is for dry operation only. It is not

waterproof. Never put the shaver

in part or completely into water.

■ Never clean the shaver or replace

the cutters while it is plugged into

an electrical outlet.

■ Do not use an aggressive cleansing

agent as this may destroy the

shaver coatings.

■ Do not clean or remove the head

assem

bly while the shaver is

When is it Time to Replace

Your Heads and Cutters?

It is very important to replace your

heads and cutters when necessary

to ensure a close, comfortable shave

without irritation. We recommend

they be replaced every 12 months.

Here are some signs of head and

cutter wear, indicating that replace

-

ment is needed.

Irritation

As the heads get excessively worn

you may experience some skin

irritation. This would be especially

noticeable when you apply after-

shave lotion.

Pulling

When the cutters wear you may

feel a sense of pulling and a loss of

closeness when you shave. This is

an indication that it is time to replace

your heads and cutters.

The replacement part for this shaver

is model #SP-29.

U.S. residents: To order, contact us

at 800-736-4648, visit us at

www.remington-products.com or

visit your local retailer.

Canadian residents: For any shaver

accessory requirements, please call

800-268-0425 or write: Spectrum

Brands Canada, Inc., Mississauga,

ON L4W 2T7.

Head/frame

assembly

Floating

cutter

heads

Locating pins

Cutter retainer

assembly

Center

screw

knob

Locating holes

! Important: Make sure to align

the two locating holes in the Cutter

Retainer assembly with the pins

in the Head Frame Assembly. (See

illustration below). Then tighten

center screw knob to lock the cutters

into place.Replace head assembly on

the shaver simply by pushing it onto

the shaver. Cover shaver head with

plastic headguard between uses.

When removing the headguard or

placing it back onto the shaver, do

not apply pressure to floating cutter

surfaces, as you may damage them.

running or plugged

in, as it may

cause damage to the unit's heads

or cutters.

■ Replace worn or damaged parts

with Remington

®

replacement

parts only.

34159_R450S-650S_IB_update.indd 10-11 5/24/07 11:05:12 AM

1 2 3 4 5 6 7 8 9 10 11 ... 22 23

Comments to this Manuals

No comments