Remington RM4625 Operator's Manual download pdf (Page 7)

FUELING THE UNIT

1. Position the unit with the fuel cap facing up.

2. Remove the fuel cap.

3. Place the fuel container spout into the fill hole on the fuel tank

and fill the tank.

NOTE: Do not overfill the tank.

4. Wipe up any fuel that may have spilled.

5. Reinstall the fuel cap.

6. Move the unit at least 30 ft. (9.1 m) from the fuel container and

the fueling site before starting the engine.

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons for the unit

not running properly. Be sure to use fresh, clean unleaded fuel.

Follow the instructions carefully for the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates such as

ethanol, methanol, or MTBE (ether). Alcohol-blended fuel absorbs

water. As little as 1% water in the fuel can make fuel and oil

separate. It forms acids when stored. When using alcohol-blended

fuel, use fresh fuel (less than 30 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable, follow

recommended precautions:

• Always use the fresh fuel mix explained in your operator's manual

• Use the fuel additive STA-BIL® or an equivalent

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit contains a fuel

additive which will help inhibit corrosion and minimize the formation

of gum deposits. It is recommended that you use our 2-cycle oil

with this unit.

If unavailable, use a good 2-cycle oil designed for air-cooled

engines along with a fuel additive, such as STA-BIL Gas Stabilizer or

an equivalent. Add 0.8 oz. (23 ml) of fuel additive per gallon of fuel

according to the instructions on the container. NEVER add fuel

additives directly to the unit's fuel tank.

Mixing the Fuel

Thoroughly mix the proper ratio of 2-cycle engine oil with unleaded

gasoline in a separate fuel can. Use a 40:1 fuel/oil ratio. Do not mix

them directly in the engine fuel tank. See the table below for specific

gas and oil mixing ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with one

3.2 oz. (95 ml) bottle of 2-cycle oil makes a 40:1 fuel/oil ratio.

NOTE: Dispose of the old fuel/oil mix according to federal, state and

local regulations.

WARNING: Remove fuel cap slowly to avoid injury from

fuel spray. Never operate the unit without the fuel cap

securely in place.

WARNING: Add fuel in a clean, well ventilated outdoor

area. Wipe up any spilled fuel immediately. Avoid creating

a source of ignition for spilt fuel. Do not start the engine

until fuel vapors dissipate.

CAUTION: For proper engine operation and maximum

reliability, pay strict attention to the oil and fuel mixing

instructions on the 2-cycle oil container. Using improperly

mixed fuel can severely damage the engine.

WARNING: Gasoline is extremely flammable. Ignited

vapors may explode. Always stop the engine and allow it

to cool before filling the fuel tank. Do not smoke while

filling the tank. Keep sparks and open flames at a distance

from the area.

OIL AND FUEL

Unleaded gasoline* 2-cycle oil

1 gallon U.S.

(3.8 liters)

3.2 fl. oz.

(95 ml)

1 liter 25 ml

MIXING RATIO - 40:1

*WARNING: DO NOT USE E85 FUEL IN THIS UNIT.

It has been proven that fuel containing greater than 10%

ethanol will likely damage this engine and void the warranty.

1 2 3 4 5 6 7 8 9 10 11 12 ... 47 48

Comments to this Manuals

No comments

Remington RM4625 Operator's Manual Page 7

Comments to this Manuals

Related products and manuals for Mini tillers Remington RM4625