Use & Care Guide
THIS CURLING BRUSH CAN ALSO BE USED
AS A 3/4” CURLING IRON BY REMOVING
THE CURLING BRUSH ATTACHMENT
1. Unplug the unit and let it cool completely.
Remove brush attachment by holding the unit
firmly by the handle and sliding off Curling Brush.
3. Plug in and let heat.
FOLLOW THE SAME INSTRUCTIONS IN THIS
BOOK WHEN USING UNIT AS A CURLING IRON.
HOW TO GET PROFESSIONAL RESULTS
WITH YOUR CURLING BRUSH
This unique curling brush has been designed with
multiple temperatures, providing very high heat in
the Hl (25-30) settings for curling very coarse,
thick, hard-to-curl hair, and very low heat in the
LO (1-6) settings for curling extra fine, damaged
or dry hair. It also provides a full range of heat
settings between LO and HI, for all normal
textures and thicknesses of hair.
TEST A SMALL SECTION OF HAIR BEFORE
USING; THEN ADJUST TEMPERATURE
DEPENDING ON TYPE OF HAIR.
This multiple temperature curling brush has been
specially designed to curl very coarse, thick, hard-
to-curl hair. Due to this special application, the
barrel of this curling brush will be hotter on the HI
(25-30) settings than regular dual-heat curling
brushes. Due to the extreme capabilities of
this brush, the barrel will be very hot in the
HI (25-30) settings, so extra care should be
taken when using.
• Keep unit away from contact with all skin
areas. Do not touch barrel with fingertips.
• For shorter hair, place a thin plastic comb
between scalp and curling brush to avoid
• Place fingers of free hand on safety tip when
more control is needed
• Test small section of hair to
determine correct heat setting for
the type of hair being styled.
These settings are very hot. Use only if hair
is very coarse and highly resistant, but in
Use heat settings in this range for dense,
hard-to-curl hair in good condition.
Use heat settings in this range for thick, wavy hair
in good condition.
Use heat settings in this range for easy-to-curl,
Use LO heat setting for very fine, fragile, damaged
This brush features solid-state electronic
circuitry with a heat sensor that detects
temperature loss and quickly boosts the
power to bring the heat level back to
optimum styling temperature. This allows
for styling in half the time it takes with an
This appliance is designed to operate on
120/240 volts, 50/60 Hz. It is not intend-
ed for commercial use. Hair should be
clean, dry or nearly dry, and free of tan-
gles before using.
HOW TO USE
For complete styling, hair should be clean,
dry and free from dirt, hair spray, creams,
etc. (This curling brush can also be used
for quick touch-ups any time.)
1. Rest the curling brush on a smooth,
flat surface, and plug it in.
2. Press ON/OFF switch, and the power
indicator light will flash.
3. Select a temperature according to the
type and texture of hair to be styled.
4. With heat control dial set at desired
position, allow unit to pre-heat. The
power indicator light will begin to
flash to signal that appliance is heat-
ing up. When appliance is fullly heat-
ed the indicator light will stop flash-
ing. Note: For optimum styling per-
formance, let the brush continue to
heat for about 2 minutes before using.
How to Use (con’t)
1. To clean the unit, be sure it is cool
and unplugged. Wipe handle,
barrel and curling brush with a
damp cloth. No other maintenance
2. When not in use, store appliance
where it will not become damaged.
Do not wrap cord around
3. Do not attempt to repair the appliance
yourself. Return to Remington
Customer Service Center for repair.
When not in use, unplug the unit. Allow it
to cool and store out of reach of children in
a safe, dry location.
Never wrap the cord around the appliance
as this will cause the cord to wear prema-
and break. Handle cord carefully
and avoid jerking it, twisting or straining it,
especially at plug connections.
1. Taking one section at a time, use the curling
brush to roll hair in the direction of the curl
desired, and hold a few seconds.
2. When using as a curling iron, take one sec-
tion at a time, lift clamp and place end of hair
under the clamp so that it extends a little past
the clamp. Release clamp so that it closes
over the end of the hair. Roll hair in desired
direction and hold for a few seconds.
3. The cool tip can be a great help in winding.
Use one hand on the handle and the fingers
of the other on the cool tip.
NOTE: To avoid tangling, do not wind
hair around the curling brush more
than two times.
3. When hair feels warm, the curl is set.
4. Carefully remove curling brush and allow
curl to cool without disturbing it.
5. Continue steps 1-4 all over your head.
6. When you achieve your desired style, use
the hot brush to brush hair into place.
7. Afterward, once all curls have cooled thor-
oughly, gently brush and comb hair into the
■ For a Flip, take a 2" section of hair and roll
the brush up over the hair.
■ For a Curl, take a 2" section of hair and roll
the brush under the hair.
■ For Volume and Body, roll hair loosely
around the brush. Allow hair to cool slightly
After approximately one hour, the unit will
automatically shut itself off. To reactivate
the unit, press ON/OFF switch.
DUAL VOLTAGE USE
This product contains a special electronic circuit.
This circuit automatically adjusts to worldwide
voltage. When traveling overseas, this product
can be plugged into any voltage outlet without
your having to adjust the product manually in any
way. In some overseas countries, an attachment
plug adapter of the proper configuration for the
power supply receptacle may be required. DO
NOT USE a voltage converter or extension cord
with this product.
Curling Brush and Iron
with 3X Protection
for beautiful, healthy,