Remington PG6030 User Manual download pdf (Page 3)

4 5

ENGLISHENGLISH

any waxes or lotions before using the groomer

,To thin and taper beards or moustache

• Attach the wide trimmer blade.

• Place the hair length attachment on the trimmer blade, select the desired length and

switch on.

• Start trimming under the chin, following the jawbone line. Work toward the ear and

upper beard line using an upward motion.

,To trim edge of beard or moustache

• Attach the detail trimmer blade.

• Hold groomer with cutting blade facing you.

• Start with edge of beard/moustache line, and with the cutting blades resting lightly

against your skin, use slow movements to create a beard/moustache line.

,To trim sideburns

• Hold groomer with cutting blade facing you.

• Use a small comb to lift the hairs. Hold the comb at the desired beard or moustache

length.

• Move the groomer along the comb to cut the hairs. Use light pressure and well-controlled

movements to trim hair.

,Trimming the nape of your neck

• Attach the wide trimmer blade.

• Use your ngers to lift the hair at the base of your head up o the neck. Your index nger

should be covering the roots of the hairs you are lifting to prevent accidental removal by

groomer.

• Using your other hand, hold the groomer to the base of your neck with the cutting unit

facing up, and move the groomer up the length of the neck until the unit touches your

nger covering the hair roots at the base of your head.

Move the unit slowly when performing this operation and to keep the hair roots at the

base of your head out of the way of the groomer.

,To remove hair from nose and ear

• Attach nose, ear & eyebrow attachment.

• Insert groomer’s cutting unit gently into the nostril or ear.

• Gently move the groomer in and out of the nostril or ear and at the same time rotate the

groomer.

• Avoid inserting the cutting unit more than 6mm into your nostril or ear.

,To remove hair from eyebrows

• Attach nose, ear, eyebrow attachment.

• Gently guide cutting unit to stray, unwanted hairs along the eyebrow line or protruding

from the eyebrow itself.

• To remove the hairs completely lower onto the skin and move over desired area.

• Use slow and well-controlled movements.

ETips for best results

Comb your hair in the direction that it grows so that the hairs are at their maximum height and

facing in the same direction.

After trimming, lightly go over the trimmed areas with the foil to get a smooth clean nish.

Since all hairs do not grow in the same direction, you may want to try dierent trimming

positions (i.e. upwards, downwards or across) for better results.

,Attaching and removing the trimmer attachments.

Note: Always ensure the groomer is switched o before changing any attachments.

• To remove, hold the groomer with one hand and turn the trimmer head anti-clockwise

with the other.

• To attach, hold the groomer with on hand and turn the trimmer head clockwise with the

other.

,Using the detailed trimmer

• Hold groomer with the surface (back side) of the blade guides against the skin.

• Use motions similar to using a wet blade to provide the closest trim.

Note: This attachment provides a dual purpose solution for stubble or close results

without irritation.

,Using your miniscreen shaver

• Hold the groomer so the MiniScreen gently touches your face.

• Use short, and well-controlled movements to shave around your beard/moustache. Use

your free hand to stretch your skin. This encourages the hair to stand upright, making it

easier to shave.

Note: The MiniScreen shaver was designed to shave the detail areas around your beard

moustache/sideburns. It was not designed to shave your entire face. For a close

comfortable shave, guaranteed, use one of Remington’s electric shavers.

C CARE FOR YOUR GROOMER

Care for your product to ensure a long lasting performance. We recommend that you clean your

groomer after each use.

The easiest and the most hygienic way to clean the groomer is by rinsing the product head after

use with warm water. Always keep the protective cap on the shaving head and keep the trimmer

in the “o” position when the shaver is not in use.

E After each use

• Rinse the accumulated hair from the cutters and shake o excess water. Alternatively, use

a brush.

• Gently tap on a at surface to remove hair particles, and brush the remaining hairs away.

• Place one or two drops of cutter oil or sewing machine oil on the blades. Turn the clipper

on to distribute the oil evenly, wipe o any excess oil.

• Wipe the main unit with a damp cloth and dry immediately.

Note: Ensure that the groomer is turned o when applying

the oil or rinsing under the tap.

1 2 3 4 5 6 7 8 ... 59 60

Comments to this Manuals

No comments

Remington PG6030 User Manual Page 3

Comments to this Manuals

Related products and manuals for Hair clippers Remington PG6030